德國企業尋求低延展性金屬（超高強度鋼，鋁，錳）成型技術
德國一家跨國汽車零部件供應商尋求低延展性金屬成型技術，以進行大容量應用。仍出于實驗室階段和已經充分開發的技術均可。該公司在歐洲（主要是德國），北美和亞洲擁有研發機構，歡迎能夠提供相應解決方案的企業，研究機構和教育機構通過特許權協議或共同開發的方式進行合作。
技術條件/要求：
公司尋求符合以下條件的技術。若技術不能達到目前的要求，需保證其有潛力在最多兩年的發展期內達到要求。
能夠?qū)??xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />1毫米左右厚度的低延展性金屬進行小半徑，鋒利形變和深沖壓加工。
能夠快速將金屬加熱到以下溫度區間的溫度：能夠?qū)?st1:chmetcnv w:st="on" UnitName="毫米" SourceValue="600" HasSpace="False" Negative="False" NumberType="1" TCSC="0">600毫米x800毫米x<1.2毫米的坯料在10秒周期時間內加熱到250攝氏度-900攝氏度。
公司對激光加熱技術進行了調查研究，但需要此項技術的去本地化解決方案。由于預熱問題和材料本身的厚度，材料從熱爐轉移到機床的過程中會難以保持溫度和穩定性。理想的解決方案是類似于機床內加熱技術，能夠避免材料的轉移和機床壽命的減少。
英文原文:
Technologies to form metals with low ductility (ultra high strength steel, aluminum, magnesium...) (12 DE 0855 3PZD)
A multinational automotive supplier with research and development locations in Europe (in particular Germany), North America and Asia is seeking technologies to form metals with low ductility for high volume applications. The technology offered can either be at laboratory stage or fully developed. Industry, research organizations and academia with suitable solutions are welcome for a licensing agreement or joint development.
Technical Specifications / Specific technical requirements:
The company is seeking a technology that meets the following specifications. If the technology is not able to meet the specifications today, there should be a promising potential that it will do so within a development time of up to two years.
- Production of tight radii, sharp shape changes and deep draw in low ductility metals on the order of 1mm thick.
- Interest in technologies that can rapidly heat metals to one of two temperature ranges: approximately 250C and 900C - for 600mm x 800mm x <1.2mm blank with less than 10 second cycle times.
The company has investigated laser heating, but needs a non-localised solution. With preheat and material thickness, material handling from oven to tool makes maintenance of temperature and material stability difficult. An ideal solution could look like in-tool heating without material transfer and degradation of tool life.
